Jump to content

Wastewater treatment

From Wikipedia, the free encyclopedia
(Redirected from Wastewater Treatment)
This article is about the treatment of any type of wastewater from a range of sources. For treatment of wastewater from households or municipalities (domestic wastewater), see Sewage treatment.
Sewage treatment plant (a type of wastewater treatment plant) in La Crosse, Wisconsin

Wastewater treatment is a process which removes and eliminates contaminants from wastewater. It thus converts it into an effluent that can be returned to the water cycle. Once back in the water cycle, the effluent creates an acceptable impact on the environment. It is also possible to reuse it. This process is called water reclamation.[1] The treatment process takes place in a wastewater treatment plant. There are several kinds of wastewater which are treated at the appropriate type of wastewater treatment plant. For domestic wastewater the treatment plant is called a Sewage Treatment. Municipal wastewater or sewage are other names for domestic wastewater. For industrial wastewater, treatment takes place in a separate Industrial wastewater treatment, or in a sewage treatment plant. In the latter case it usually follows pre-treatment. Further types of wastewater treatment plants include Agricultural wastewater treatment and leachate treatment plants.

One common process in wastewater treatment is phase separation, such as sedimentation. Biological and chemical processes such as oxidation are another example. Polishing is also an example. The main by-product from wastewater treatment plants is a type of sludge that is usually treated in the same or another wastewater treatment plant.[2]: Ch.14  Biogas can be another by-product if the process uses anaerobic treatment. Treated wastewater can be reused as reclaimed water.[3] The main purpose of wastewater treatment is for the treated wastewater to be able to be disposed or reused safely. However, before it is treated, the options for disposal or reuse must be considered so the correct treatment process is used on the wastewater.

The term "wastewater treatment" is often used to mean "sewage treatment".[4]

Types of treatment plants

[edit]

Wastewater treatment plants may be distinguished by the type of wastewater to be treated. There are numerous processes that can be used to treat wastewater depending on the type and extent of contamination. The treatment steps include physical, chemical and biological treatment processes.[citation needed]

Types of wastewater treatment plants include:

Sewage treatment plants

[edit]
This section is an excerpt from Sewage treatment.[edit]

Sewage treatment (or domestic wastewater treatment, municipal wastewater treatment) is a type of wastewater treatment which aims to remove contaminants from sewage to produce an effluent that is suitable to discharge to the surrounding environment or an intended reuse application, thereby preventing water pollution from raw sewage discharges.[5] Sewage contains wastewater from households and businesses and possibly pre-treated industrial wastewater. There are a high number of sewage treatment processes to choose from. These can range from decentralized systems (including on-site treatment systems) to large centralized systems involving a network of pipes and pump stations (called sewerage) which convey the sewage to a treatment plant. For cities that have a combined sewer, the sewers will also carry urban runoff (stormwater) to the sewage treatment plant. Sewage treatment often involves two main stages, called primary and secondary treatment, while advanced treatment also incorporates a tertiary treatment stage with polishing processes and nutrient removal. Secondary treatment can reduce organic matter (measured as biological oxygen demand) from sewage,  using aerobic or anaerobic biological processes. A so-called quarternary treatment step (sometimes referred to as advanced treatment) can also be added for the removal of organic micropollutants, such as pharmaceuticals. This has been implemented in full-scale for example in Sweden.[6]

A large number of sewage treatment technologies have been developed, mostly using biological treatment processes. Design engineers and decision makers need to take into account technical and economical criteria of each alternative when choosing a suitable technology.[7]: 215  Often, the main criteria for selection are: desired effluent quality, expected construction and operating costs, availability of land, energy requirements and sustainability aspects. In developing countries and in rural areas with low population densities, sewage is often treated by various on-site sanitation systems and not conveyed in sewers. These systems include septic tanks connected to drain fields, on-site sewage systems (OSS), vermifilter systems and many more. On the other hand, advanced and relatively expensive sewage treatment plants may include tertiary treatment with disinfection and possibly even a fourth treatment stage to remove micropollutants.[6]

At the global level, an estimated 52% of sewage is treated.[8] However, sewage treatment rates are highly unequal for different countries around the world. For example, while high-income countries treat approximately 74% of their sewage, developing countries treat an average of just 4.2%.[8]
Aeration tank of an activated sludge process at the wastewater treatment plant in Dresden-Kaditz, Germany

Industrial wastewater treatment plants

[edit]
This section is an excerpt from Industrial wastewater treatment.[edit]
Wastewater from an industrial process can be converted at a treatment plant to solids and treated water for reuse.

Industrial wastewater treatment describes the processes used for treating wastewater that is produced by industries as an undesirable by-product. After treatment, the treated industrial wastewater (or effluent) may be reused or released to a sanitary sewer or to a surface water in the environment. Some industrial facilities generate wastewater that can be treated in sewage treatment plants. Most industrial processes, such as petroleum refineries, chemical and petrochemical plants have their own specialized facilities to treat their wastewaters so that the pollutant concentrations in the treated wastewater comply with the regulations regarding disposal of wastewaters into sewers or into rivers, lakes or oceans.[9]: 1412  This applies to industries that generate wastewater with high concentrations of organic matter (e.g. oil and grease), toxic pollutants (e.g. heavy metals, volatile organic compounds) or nutrients such as ammonia.[10]: 180  Some industries install a pre-treatment system to remove some pollutants (e.g., toxic compounds), and then discharge the partially treated wastewater to the municipal sewer system.[11]: 60 

Most industries produce some wastewater. Recent trends have been to minimize such production or to recycle treated wastewater within the production process. Some industries have been successful at redesigning their manufacturing processes to reduce or eliminate pollutants.[12] Sources of industrial wastewater include battery manufacturing, chemical manufacturing, electric power plants, food industry, iron and steel industry, metal working, mines and quarries, nuclear industry, oil and gas extraction, petroleum refining and petrochemicals, pharmaceutical manufacturing, pulp and paper industry, smelters, textile mills, industrial oil contamination, water treatment and wood preserving. Treatment processes include brine treatment, solids removal (e.g. chemical precipitation, filtration), oils and grease removal, removal of biodegradable organics, removal of other organics, removal of acids and alkalis, and removal of toxic materials.

Agricultural wastewater treatment plants

[edit]
This section is an excerpt from Agricultural wastewater treatment.[edit]
Anaerobic lagoon for treatment of dairy wastes

Agricultural wastewater treatment is a farm management agenda for controlling pollution from confined animal operations and from surface runoff that may be contaminated by chemicals in fertilizer, pesticides, animal slurry, crop residues or irrigation water.

Agricultural wastewater treatment is required in continuous confined animal management operations like milk and egg production. It may be performed in plant management operations using mechanized treatment units similar to those used for industrial wastewater. Where land is available for ponds, settling basins and facultative lagoons to lower operational costs for seasonal use conditions from breeding or harvest cycles.[13]: 6–8  Animal slurries are usually treated by containment in anaerobic lagoons before disposal by spray or trickle application to grassland. Constructed wetlands are sometimes used to facilitate treatment of animal wastes.

Leachate treatment plants

[edit]
Main article: Leachate § Treatment

Leachate treatment plants are used to treat leachate from landfills. Treatment options include: biological treatment, mechanical treatment by ultrafiltration, treatment with active carbon filters, electrochemical treatment including electrocoagulation by various proprietary technologies and reverse osmosis membrane filtration using disc tube module technology.[14]

Unit processes

[edit]
See also: List of wastewater treatment technologies
Diagram of a typical surface-aerated basin for wastewater treatment

The unit processes involved in wastewater treatment include physical processes such as settlement or flotation and biological processes such oxidation or anaerobic treatment. Some wastewaters require specialized treatment methods. At the simplest level, treatment of most wastewaters is carried out through separation of solids from liquids, usually by sedimentation. By progressively converting dissolved material into solids, usually a biological floc or biofilm, which is then settled out or separated, an effluent stream of increasing purity is produced.[2][page needed][15]

Phase separation

[edit]
Clarifiers are widely used for wastewater treatment.

Phase separation transfers impurities into a non-aqueous phase. Phase separation may occur at intermediate points in a treatment sequence to remove solids generated during oxidation or polishing. Grease and oil may be recovered for fuel or saponification. Solids often require dewatering of sludge in a wastewater treatment plant. Disposal options for dried solids vary with the type and concentration of impurities removed from water.[16]

Primary settling tank of wastewater treatment plant in Dresden-Kaditz, Germany

Sedimentation

[edit]
Further information: Sedimentation (water treatment) and Sewage treatment § Primary treatment

Solids such as stones, grit, and sand may be removed from wastewater by gravity when density differences are sufficient to overcome dispersion by turbulence. This is typically achieved using a grit channel designed to produce an optimum flow rate that allows grit to settle and other less-dense solids to be carried forward to the next treatment stage. Gravity separation of solids is the primary treatment of sewage, where the unit process is called "primary settling tanks" or "primary sedimentation tanks".[17] It is also widely used for the treatment of other types of wastewater. Solids that are denser than water will accumulate at the bottom of quiescent settling basins. More complex clarifiers also have skimmers to simultaneously remove floating grease such as soap scum and solids such as feathers, wood chips, or condoms. Containers like the API oil-water separator are specifically designed to separate non-polar liquids.[18]: 111–138 

Biological and chemical processes

[edit]

Oxidation

[edit]

Oxidation reduces the biochemical oxygen demand of wastewater, and may reduce the toxicity of some impurities. Secondary treatment converts organic compounds into carbon dioxide, water, and biosolids through oxidation and reduction reactions.[19] Chemical oxidation is widely used for disinfection.[20]

Biochemical oxidation (secondary treatment)
[edit]
This section is an excerpt from Secondary treatment.[edit]
This small secondary clarifier at a rural sewage treatment plant is a typical phase separation mechanism to remove biological solids formed in a suspended growth or fixed-film bioreactor.
Secondary treatment (mostly biological wastewater treatment) is the removal of biodegradable organic matter (in solution or suspension) from sewage or similar kinds of wastewater.[21]: 11  The aim is to achieve a certain degree of effluent quality in a sewage treatment plant suitable for the intended disposal or reuse option. A "primary treatment" step often precedes secondary treatment, whereby physical phase separation is used to remove settleable solids. During secondary treatment, biological processes are used to remove dissolved and suspended organic matter measured as biochemical oxygen demand (BOD). These processes are performed by microorganisms in a managed aerobic or anaerobic process depending on the treatment technology. Bacteria and protozoa consume biodegradable soluble organic contaminants (e.g. sugars, fats, and organic short-chain carbon molecules from human waste, food waste, soaps and detergent) while reproducing to form cells of biological solids. Secondary treatment is widely used in sewage treatment and is also applicable to many agricultural and industrial wastewaters.
Chemical oxidation
[edit]
Main article: Advanced oxidation process

Advanced oxidation processes are used to remove some persistent organic pollutants and concentrations remaining after biochemical oxidation.[18]: 363–408  Disinfection by chemical oxidation kills bacteria and microbial pathogens by adding hydroxyl radicals such as ozone, chlorine or hypochlorite to wastewater.[2]: 1220  These hydroxyl radical then break down complex compounds in the organic pollutants into simple compounds such as water, carbon dioxide, and salts.[22]

Anaerobic treatment

[edit]

Anaerobic wastewater treatment processes (for example UASB, EGSB) are also widely applied in the treatment of industrial wastewaters and biological sludge.

Polishing

[edit]
Further information: Sewage treatment § Fourth treatment stage

Polishing refers to treatments made in further advanced treatment steps after the above methods (also called "fourth stage" treatment). These treatments may also be used independently for some industrial wastewater. Chemical reduction or pH adjustment minimizes chemical reactivity of wastewater following chemical oxidation.[18]: 439  Carbon filtering removes remaining contaminants and impurities by chemical absorption onto activated carbon.[2]: 1138  Filtration through sand (calcium carbonate) or fabric filters is the most common method used in municipal wastewater treatment.

See also

[edit]

References

[edit]
  1. ^ "wastewater treatment | Process, History, Importance, Systems, & Technologies". Encyclopedia Britannica. October 29, 2020. Retrieved 2020-11-04.
  2. ^ a b c d Metcalf & Eddy Wastewater Engineering: Treatment and Reuse (4th ed.). New York: McGraw-Hill. 2003. ISBN 0-07-112250-8.
  3. ^ Takman, Maria; Svahn, Ola; Paul, Catherine; Cimbritz, Michael; Blomqvist, Stefan; Struckmann Poulsen, Jan; Lund Nielsen, Jeppe; Davidsson, Åsa (2023-10-15). "Assessing the potential of a membrane bioreactor and granular activated carbon process for wastewater reuse – A full-scale WWTP operated over one year in Scania, Sweden". Science of the Total Environment. 895: 165185. Bibcode:2023ScTEn.89565185T. doi:10.1016/j.scitotenv.2023.165185. ISSN 0048-9697. PMID 37385512. S2CID 259296091.
  4. ^ Tchobanoglous, George; Burton, Franklin L.; Stensel, H. David (2003). Metcalf & Eddy Wastewater Engineering: Treatment and Reuse (4th ed.). McGraw-Hill. ISBN 978-0-07-112250-4.
  5. ^ Khopkar, S.M. (2004). Environmental Pollution Monitoring And Control. New Delhi: New Age International. p. 299. ISBN 978-81-224-1507-0.
  6. ^ a b Takman, Maria; Svahn, Ola; Paul, Catherine; Cimbritz, Michael; Blomqvist, Stefan; Struckmann Poulsen, Jan; Lund Nielsen, Jeppe; Davidsson, Åsa (2023-10-15). "Assessing the potential of a membrane bioreactor and granular activated carbon process for wastewater reuse – A full-scale WWTP operated over one year in Scania, Sweden". Science of the Total Environment. 895: 165185. Bibcode:2023ScTEn.89565185T. doi:10.1016/j.scitotenv.2023.165185. ISSN 0048-9697. PMID 37385512. S2CID 259296091.
  7. ^ Von Sperling, M. (2007). "Wastewater Characteristics, Treatment and Disposal". Water Intelligence Online. 6. doi:10.2166/9781780402086. ISSN 1476-1777. Text was copied from this source, which is available under a Creative Commons Attribution 4.0 International License
  8. ^ a b Jones, Edward R.; van Vliet, Michelle T. H.; Qadir, Manzoor; Bierkens, Marc F. P. (2021). "Country-level and gridded estimates of wastewater production, collection, treatment and reuse". Earth System Science Data. 13 (2): 237–254. Bibcode:2021ESSD...13..237J. doi:10.5194/essd-13-237-2021. ISSN 1866-3508.
  9. ^ Tchobanoglous G, Burton FL, Stensel HD (2003). Metcalf & Eddy Wastewater Engineering: treatment and reuse (4th ed.). McGraw-Hill Book Company. ISBN 0-07-041878-0.
  10. ^ George Tchobanoglous; Franklin L. Burton; H. David Stensel (2003). "Chapter 3: Analysis and Selection of Wastewater Flowrates and Constituent Loadings". Metcalf & Eddy Wastewater engineering: treatment and reuse (4th ed.). Boston: McGraw-Hill. ISBN 0-07-041878-0. OCLC 48053912.
  11. ^ Von Sperling, M. (2007). "Wastewater Characteristics, Treatment and Disposal". Water Intelligence Online. 6. doi:10.2166/9781780402086. ISSN 1476-1777. Text was copied from this source, which is available under a Creative Commons Attribution 4.0 International License
  12. ^ "Pollution Prevention Case Studies". Washington, D.C.: U.S. Environmental Protection Agency (EPA). 2021-08-11.
  13. ^ Reed, Sherwood C. (1988). Natural systems for waste management and treatment. E. Joe Middlebrooks, Ronald W. Crites. New York: McGraw-Hill. ISBN 0-07-051521-2. OCLC 16087827.
  14. ^ "Landfills Effluent Guidelines". EPA. 2018-03-16.
  15. ^ Primer for Municipal Waste water Treatment Systems (Report). Washington, DC: US Environmental Protection Agency (EPA). 2004. EPA 832-R-04-001..
  16. ^ Ajay Kumar Mishra Smart Materials for Waste Water Applications, Wiley-Scrivener 2016 ISBN 111904118X https://onlinelibrary.wiley.com/doi/book/10.1002/9781119041214
  17. ^ Gupta, Ashok; Yan, Denis, eds. (2016-01-01), "Chapter 16 - Gravity Separation", Mineral Processing Design and Operations (Second Edition), Amsterdam: Elsevier, pp. 563–628, doi:10.1016/B978-0-444-63589-1.00016-2, ISBN 978-0-444-63589-1, retrieved 2020-11-30
  18. ^ a b c Weber, Walter J. (1972). Physicochemical processes for water quality control. New York: Wiley-Interscience. ISBN 0-471-92435-0. OCLC 389818.
  19. ^ BERGENDAHL, JOHN. "Applications of Advanced Oxidation for Wastewater Treatment" (PDF). Dept. Of Civil & Environmental Engineering, WPI. Archived (PDF) from the original on 2017-08-29.
  20. ^ "Water Disinfection - an overview | ScienceDirect Topics". www.sciencedirect.com. Retrieved 2023-03-02.
  21. ^ Wastewater engineering : treatment and reuse. George Tchobanoglous, Franklin L. Burton, H. David Stensel, Metcalf & Eddy (4th ed.). Boston: McGraw-Hill. 2003. ISBN 0-07-041878-0. OCLC 48053912.{{cite book}}: CS1 maint: others (link)
  22. ^ Deng, Yang; Zhao, Renzun (2015-09-01). "Advanced Oxidation Processes (AOPs) in Wastewater Treatment". Current Pollution Reports. 1 (3): 167–176. Bibcode:2015CPolR...1..167D. doi:10.1007/s40726-015-0015-z. ISSN 2198-6592.
[edit]
Retrieved from "https://en.wikipedia.org/w/index.php?title=Wastewater_treatment&oldid=1254706652"